Fiber Optic Center will be atECOCandIWCS- Schedule your meeting with a member of the FOC team now

Appropriate Ratios and Proper Epoxy Mixing and Centrifuge Equipment Are Key

For optimum 2-part epoxy bonding, it is essential that the two components, resin and hardener, (often referred to as Part A and Part B), are combined in the appropriate ratios and adequately mixed prior to dispensing and applying to the product.

When manually measuring out the quantities of separate bulk packages of Part A and B, an accurate weight scale with suitable resolution (depending on the total quantities you are preparing) is necessary.An electronic scale with a "tare" function is helpful.Suitable ratios of each part can be measured into a suitable clean cup, and mixed with a clean, dust / lint / splitter-free mixing stick.

Epoxy packaged in bi-packs are by far the most commonly used in professional fiberoptic connector termination scenarios.Bi-packs are a single plastic sleeve containing accurately-measured ratios of Part A and B.These are separated by either a clip or a burst-seal to prevent the two parts from coming into contact until you are ready to use.This is very handy in the production line, as it obviates the need for measuring on the production floor and reduces operator handling of the epoxy components.

The epoxy components are often "hazardous materials" that can pose health risks if not properly handled with suitable PPE (gloves and eye protection).To mix the two epoxy components in a bi-pack, the separator clip is removed, or the burst-seal is broken, and a roller (such as a typical lamination roller) is used to mix the two components together within the closed plastic sleeve.

Bi-packs can also be mixed by machines built specifically for this process, which helps ensure consistent and repeatable mixing.They often are designed for smaller (2.5 – 10 gram) bi-packs, so be sure to verify that your desired bi-pack size is compatible with such equipment.

Epoxy also can be packaged in "dual-tube" cartridges using a purpose-built dispensing gun similar to how a typical caulk or silicon sealant gun is used.Instead of one tube, there are two tubes, Part A and B, usually of different diameter to help ensure proper ratios are dispensed.A mixing-nozzle is attached to the dispensing end, and the two parts are pushed through the mixing nozzle as the gun plunger pushes from the back.

If mixing with a stick, as with bulk-packaged epoxy, or with a roller, as with bi-pack packaged epoxy, air bubbles are inevitably introduced to the mixed epoxy, and MUST be removed prior to injection into connectors.

De-gassing the epoxy after mixing and prior to applying is very important and failure to do so can result in serious long-term reliability risks to the product (air bubbles trapped within cured epoxy can present permanent stress to the delicate fiber within the connector).De-gassing is most commonly done by use of acentrifuge.Epoxy can also be de-gassed by subjecting the mixed epoxy to the vacuum in a vacuum chamber, though this is less common and un-necessarily complicated for most epoxies used for connector termination.

Variable-speed centrifuges are available, but single fixed-speed centrifuges are more common and usually sufficient.Most epoxies can safely be de-gassed with fixed centrifuge speeds in the 2500-3500 RPM range.Be aware that if you are using epoxies with additives, such as dyes for coloring, excessive RPM can separate out heavier additives, leading to a non-homogeneous epoxy mix which can significantly degrade your epoxy bonding characteristics.

Vacuum de-gassing is commonly reserved only for epoxies which cannot be easily de-gassed via centrifuge.An example would be very thick, high viscosity epoxies which are not common in normal termination applications.

乐动体育在线客服点不开The Fiber Optic Center Technical Team provides consultation on the exact type ofcentrifuge and mixing equipmentbest suited for specific applications and the viscosity of the epoxy being used.Choosing the correct method as well as proper centrifuge and mixing equipment will impact the quality and reliability of the finished fiber optic product.

About the Author
Dan Rocheleau Dan Rocheleau, Business Development, Technical Sales Dan has worked in fiber optic cable assembly since 1986: starting as a part-time line operator for a local cable production company and working his way up through to management positions in large global companies.His experience includes positions in process training, supervision, product and process engineering, quality system development and management, factory general management, global factory startups, and global project management roles.He has held several overseas positions, opening and managing factories in Mexico, India, China, and Czech Republic.He has led global project efforts in sourcing / supplier auditing, global process standardization, and global operations strategic planning.Dan's extensive experience gives him a unique ability to relate to our customer's needs and challenges, helping Fiber Optic Center better help our customers continue to adapt and grow in the evolving and competitive fiber cable assembly market.
Kathleen Skelton Kathleen Skelton, Director of Strategic Marketing, has worked in the fiber optic, cable and connector industries for over three decades.Her core competencies in fiber optics include technologies that enable the growth, integration and performance scalability of voice, data and video communications networks and services, having worked with a majority of the strategy managers in the industry during her tenure with Lightwave.Kathleen's marketing expertise resides in business development, strategic and digital best practices and content management.Kathleen resides outside of Boston, MA with her family.Follow @KATHLEENSKELTON
About Fiber Optic Center, Inc.
Fiber Optic Center, Inc., (FOC), is an international leader in distributing fiber optic components, equipment and supplies and has been helping customers make the best cable assemblies in the world for over two decades.Several areas of specialization and expertise, in which they are the industry leader, make them the preferred choice for many of the world's fiber professionals.In these key technology areas, FOC is "at least as technical as the manufacturer" about the products they sell.Striving to "make the business part easy," they offer outstanding and personal customer service, low or no minimum purchase order values, and from-stock delivery on industry-leading products and technology.FOC is the industry connection to the most innovative optical products, technologies and technical experts who integrate their manufacturing knowledge and vast experience into customers' worldwide operations. @FiberOpticCntr

For further information contact:
Fiber Optic Center, Inc., 23 Centre Street, New Bedford, MA 02740-6322
Toll Free in US: 800-IS-FIBER or 800-473-4237 .Direct 508-992-6464.Email: sales@www.spnnc.comor fiberopticcenter@www.spnnc.com

For media contact:
Kathleen Skelton, Director of Strategic Marketing, C: 617-803-3014 .E: kskelton@www.spnnc.com
Baidu
map